 |
| RDS Weigh Log 100 |
| On-Board
Skidsteer Scales |
Suitable for agricultural loaders, shovels, compact
wheeled loaders, front-end
loaders, forklifts, telescopic
handlers and other vehicles with
numerous attachments.. |
| • Operating
Voltage: 11-30 Vdc |
|
|
|
|
The RDS WeighLog 100 provides a low cost solution for various Industrial and Agricultural needs. The RDS WeighLog 100 measures hydraulic pressure at a specific position on the lifting cycle either Dynamically (as the load is being lifted) or Statically (where the load is being lifted to a pre-set reference position where it is held until a reading is calculated).
The RDS WeighLog 100 has 5 individual display channels available, which can be calibrated for up to 5 different loader attachments or can be used to record quantities of five different commodities/ingredients. Each channel will display the Net bucket weight at each lift which then can be added to the total for the channel in use if required.
|
 |
- Static or Dynamic Weighing
|
- 5 individual display channels
|
|
- Backlit LCD graphic display and keypad
|
|
|
| WEIGHING
MODE The system is based on the measurement of the pressure
of the lifting cylinder in the up phase (by means of the pressure
transducer) and the calculation of the up speed. Accurate weight is achieved after the arm has passed the proximity switches. To perform the weighing just lift the arm keeping
the motor revs constant is recommended, but not necessary. It is recommended practice to keep the lifting lever hooked and wait for
the unit to give the whistle which signals when the system is performing
the weighing. It is important during this the upward movement must remain constant,
as must the motor revs. The machine should be level as possible
and should be subjected to as few jolts as possible. |
 |
We make it easy! Providing you with the information and parts for your install. |
|
User installable! |
|
Just
1 day to install & Calibrate! |
|
Specifications:
Operating Voltage:
|
11 - 30Vdc |
Display |
160 x 128 pixel (9.5 x 7.5cm) |
Temperature range: |
-40 to +85°C storage,
-20 to +70°C operating |
System accuracy: |
+/- 2% of capacity (or better) |
Load sensor rating: |
0 - 250 bar |
Enviro. protection: |
Instrument unit IP34, sensors IP65 |
Enclosure: |
Full RFI/EMI protection
ABS outer casing |
Dimensions: |
155 x 220 x 65mm (HxWxD) 0.75kg |
Systems
Requirements: Your hydraulic systems meet manufactures
standards. Leaks in your hydraulic system may degrade the performance
this system. |
 |
What
You Should Know!
| What
you should know about Hydraulic system. |
| • |
Do
not install scale systems on any equipment that are
poorly maintained. |
| • |
Hydraulic
leak can degrade the performance of any system. |
| • |
Under
powered equipment can cause hydraulics to surge. This is caused
by over sized attachments. |
| • |
With
each of our system you will receive helpful information that
will increase the accuracy of your system. |
| • |
Recommended for loader's with 3 yard bucket or smaller. |
|
What you
need to calibrate scale:
• Calibration of this system
requires a known weight.
Most customers calibrate with on site with available materials. Scale must be calibrated at full capacity of the loader! Load a truck, verify the weight on a truck scale. Using the nudge feature in the scale indicator, correct the calibration as needed. (If calibrated with less than full capacity of bucket the weights may not be accurate)
Note: The
weighing system is hydraulic based. The hydraulic system on the machine
MUST be free of any leaks or defects. Mechanically, the machine must
be sound. Free of play in boom upper structure. Any discrepancies in
the areas will result in improper operation of the weighing system. |
Download a PDF copy of this webpage
